Notifications
Clear all
This Forum is a place for Piper Comanche pilots to communicate and discuss technical issues
If you join or reset a password, please check your Spam Email box for emails from Admin at ComancheTechTalk.com
Please put your questions on the forum as well so everyone can read and respond. Someone else might be having similar questions.
All questions or topics on the Forums automatically get sent to the Tech team as well.
Comanche Instruments and Avionics
1
Posts
1
Users
0
Reactions
76
Views
Topic starter
27/04/2020 3:03 pm
Manifold pressure hose replacement
by Paul Michel Fenouil » Sun May 19, 2013 5:11 pm
Hello,
Topic 2592 doen't help for http://www.sacskyranch.com website seems obsolete.
PA24 single comanche serial 24-453 year 59.
I'm searching where to find a hose connector manifold pressure (Falcon MP1035-3). Falcon website did'nt answer.
It is just about 5 inches length. See parts 40 to 43 of Parts Catalog joined.
Topic 2592 doen't help for http://www.sacskyranch.com website seems obsolete.
PA24 single comanche serial 24-453 year 59.
I'm searching where to find a hose connector manifold pressure (Falcon MP1035-3). Falcon website did'nt answer.
It is just about 5 inches length. See parts 40 to 43 of Parts Catalog joined.
Thanks if you can help.
Michel
- Attachments
-
Comanche Parts Manifold.pdf- (328.66 KiB) Downloaded 17 times
Paul Michel Fenouil- Posts: 39
- Joined: Fri Oct 28, 2011 12:16 pm
Re: Manifold pressure hose replacement
by Jim Worley » Tue Jun 04, 2013 2:19 am
Michel,
I needed one of those too when I redid my panel last year and moved my MP gauge. I couldn't find any data, either. In my aircraft, '61 250, a solid aluminum line was installed from the firewall to the gauge. I ended up removing it, measuring it with calipers and ordering equivalent stock from Aircraft Spruce, fabricating my own, and installing it as an owner produced part , under my A&Ps supervision of course. Hope this helps.
I needed one of those too when I redid my panel last year and moved my MP gauge. I couldn't find any data, either. In my aircraft, '61 250, a solid aluminum line was installed from the firewall to the gauge. I ended up removing it, measuring it with calipers and ordering equivalent stock from Aircraft Spruce, fabricating my own, and installing it as an owner produced part , under my A&Ps supervision of course. Hope this helps.
v/r
Jim
Jim Worley- ICS member
- Posts: 70
- Joined: Sun Jun 14, 2009 6:10 am
Re: Manifold pressure hose replacement
by Paul Michel Fenouil » Thu Jun 06, 2013 4:35 pm
Thank you Jim,
My instrument panel have mount blocks, so MP gauge must be connected to the solid aluminium tube via a flexible hose. We finally found suitable fitting to the MP gauge port and use the same old rubber hose. Brand new hose is ordered to AircraftSpruce.
Other information: I found and order "Aircraft Hardware Standards Manual" here http://www.aircraftspruce.com/catalog/b ... ardwst.php
I hope it will help regarding all these complicate metering systems with fractional inches, thread, nipples, sockets, hose fitting and so on ...
My instrument panel have mount blocks, so MP gauge must be connected to the solid aluminium tube via a flexible hose. We finally found suitable fitting to the MP gauge port and use the same old rubber hose. Brand new hose is ordered to AircraftSpruce.
Other information: I found and order "Aircraft Hardware Standards Manual" here http://www.aircraftspruce.com/catalog/b ... ardwst.php
I hope it will help regarding all these complicate metering systems with fractional inches, thread, nipples, sockets, hose fitting and so on ...
Regards
Michel
Paul Michel Fenouil- Posts: 39
- Joined: Fri Oct 28, 2011 12:16 pm
