Forum

Notifications
Clear all

This Forum is a place for Piper Comanche pilots to communicate and discuss technical issues

If you join or reset a password, please check your Spam Email box for emails from Admin at ComancheTechTalk.com

Please put your questions on the forum as well so everyone can read and respond. Someone else might be having similar questions.

All questions or topics on the Forums automatically get sent to the Tech team as well.

Engine mounts

1 Posts
1 Users
0 Reactions
69 Views
Admin
Joined: 5 years ago
Posts: 1162
Topic starter  

Engine mounts

Postby Duane Bolin » Mon Mar 12, 2012 9:44 pm

I have been searching for engine mounts for my PA24-180 for some time. I finally acquired a set of Lord J-7402-5 as the parts manual specifies. The service manual states the top shocks are assembled so the gold colored shock is aft and the silver colored shock is forward, and the lower mounts are installed opposite of the top shocks.
My question is that the new shocks have no color coding. Both shocks in each box have a gold color and I can’t see any difference between the two shocks in each box.
Has anyone encountered this problem?

Duane

User avatar
Duane Bolin
ICS member
ICS member
 
Posts: 30
Joined: Sat Oct 25, 2008 4:45 pm

Re: Engine mounts

Postby Zach Grant L1011jock » Tue Mar 13, 2012 9:48 pm

Duane,
The color code is for the 250 only. The 180 doesnt have a "soft side"!
Zach
"Keep it above 5 feet and don't do nuthin dumb!"
User avatar
Zach Grant L1011jock
Technical Advisor
 
Posts: 1404
Joined: Mon Mar 22, 2004 4:35 pm
Location: Indianapolis KEYE

Re: Engine mounts

Postby Duane Bolin » Wed Mar 14, 2012 3:20 pm

Thanks Zach, you have solved my problem.
User avatar
Duane Bolin
ICS member
ICS member
 
Posts: 30
Joined: Sat Oct 25, 2008 4:45 pm

Re: Engine mounts

Postby greg » Thu Jun 28, 2012 3:54 pm

Duane

Where did you find the J7402-5 engine mounts for your 180. I need a set and have been unable to locate them. Aircraft Spruce said they are no longer available. Also if you don't mind me asking, how much were they?

Thanks
Greg

greg
ICS member
ICS member
 
Posts: 16
Joined: Mon Jul 28, 2008 4:09 pm
Location: McAllen, TX
  •  

Re: Engine mounts

Postby Zach Grant L1011jock » Thu Jun 28, 2012 4:14 pm

Aviall is the only source(from Piper). Lord eliminated their PMA so it has to go through the Piper markup. Not a good deal, but they are available.
Zach
"Keep it above 5 feet and don't do nuthin dumb!"
User avatar
Zach Grant L1011jock
Technical Advisor
 
Posts: 1404
Joined: Mon Mar 22, 2004 4:35 pm
Location: Indianapolis KEYE

Re: Engine mounts

Postby greg » Thu Jun 28, 2012 6:35 pm

Thanks Zach

I called Aviall and they had them in stock and actually cheaper than I expected. They are ordered and on there way.

Greg

greg
ICS member
ICS member
 
Posts: 16
Joined: Mon Jul 28, 2008 4:09 pm
Location: McAllen, TX
  •  

Re: Engine mounts

Postby Duane Bolin » Fri Jun 29, 2012 2:14 pm

I found the AN hardware for these mounts at Webco. I bought the bolts, washers, castellated nuts and cotter pins as stated in the parts manual, but could not use the castellated nuts and cotter pins because there was no way to install the nuts and pins due to clearance issues. I used friction nuts as was used in the previous installation.

Duane

User avatar
Duane Bolin
ICS member
ICS member
 
Posts: 30
Joined: Sat Oct 25, 2008 4:45 pm

Re: Engine mounts

Postby DAVEG24 » Sun Jul 01, 2012 2:58 pm

I bought a new, fresh, current date set of Lord Mounts for my 180 last February through Jepp Direct (internet). They shipped from Aviall and the cost including shipping was less than $100 per set. I think the cost was around $95 each. I posted this information at the time. You do not have to be a Jepp customer to order from Jepp Direct. At the time Aviall was stating that they did not have stock, and it would be at least two maybe three months before they had stock. The price quoted at the time was about $185 per set, so the Jepp Direct price was very attractive. The fact that they were able to get them out of Aviall was even more impressive. Good luck.

Dave Gitelman

DAVEG24
ICS member
ICS member
 
Posts: 754
Joined: Mon Feb 21, 2000 4:07 pm

   
Quote
Share: